Rack mount Spectrum Analyzer up to 9,4GHz SPECTRAN HF RSA 9000

• Frequency range: 1MHz to 9,4GHz
• DANL: -155dBm(1Hz)
• DANL with Preamp: -170dBm(1Hz)
• Max. power: +20dBm (opt. +40dBm)
• Lowest sample time: 5mS
• Resolution (RBW): 200Hz to 50MHz
• EMC filter: 200Hz, 9kHz, 120kHz, 200kHz, 1,5MHz, 5MHz
• Units: dBm, dBµV, V/m, A/m, W/m²
  dBµV/m, W/cm² etc.
• Detectors: RMS, Min/Max
• Demodulator: AM, FM, PM, GSM
• Input: 50 Ohm N, RF-input (f)
• Accuracy: +/- 1dB (typ.)
• Interface: USB 2.0/1.1/LAN
• Dimensions (L/W/D): 19 inch rack mount
• Weight: 3450gr
• Warranty: 2 years

Integrated PC:

• CPU: Intel Celeron G530 2,4GHz
• RAM: 2x2GB SO-DiMM DDR3, 1066MHz
• HDD: 320GB (5400rpm)
• External Ports: 2x USB 2.0, 2x USB 3.0, 1x Audio, 1x 10/100/1000 Mb/s Ethernet, 1x DVI-I (Analog,Digital), 1x HDMI, 1x eSATA
• Power supply: 19,5V (7,9A max.)
• Operatingsystem: Linux

Highlights:

• Exposure limit calculation and display according to DIN/VDE 0848
• Up to 100x faster sample time as V3 units
• Up to 60dB higher sensitivity as V3 units
• Low noise preamplifier (option)
• 14Bit Dual-ADC
• DDC Hardware-Filter
• 150 MIPS DSP (CPU)
• Real-time remote control via USB /LAN
• Vector (I/Q) measurement
• Real-time Peak Power Detector (option)
• Audio out for the use of PC based FFT analyzer software
• Very thick (3mm) aluminium housing offering very good screening.
• Free MAC OS, Linux and Windows software

Examples for possible analysis and measurements within frequency range (1MHz - 9,4GHz):

• Pre-Compliance-Test
• Radio & TV
• Tetra/BOS
• ISM434
• LTE800
• ISM868
• GSM900
• GSM1800
• GSM1900
• DECT
• UMTS
• WLAN
• Microwave
• Bluetooth
• WiFi
• LTE2.6
• WiMAX
• Directional Radio
• 5GHz WLAN
• PAR Radar
• etc.

• 19 inch SPECTRAN HF RSA 9000
• Power supply
• Cleaning brush
• Detailed English manual (on CD)
• Analyzer software for Mac OS, Linux and Windows (on CD)

• Option 002 (0,5ppm TCXO Time Base)
  

   This highly precise TCXO timebase, which has been especially developed for the SPECTRAN, offers significantly reduced phase noise (jitter). It will allow the use of the far narrower filters (down to 200Hz), which will in turn vastly enhance sensitivity. To fully exploit the maximum sensitivity of the HF-60100 V4, this option is indispensable! Furthermore, the TXCO timebase allows far more accurate frequency measurement and display and is therefore a MUST-HAVE for future applications like time-domain measurements or code-selective measurement of UMTS, all already in development.
  The standard accuracy without option 002 is 50ppm.

• Option 020 (15dB Low Noise Internal Preamplifier)
  

  This option provides an internal, super low-noise 15dB preamplifier, enabling maximum performance particularly when measuring extremely weak signals. It is switched via a TRUE RF switch. There really is no excuse for not ordering this one, considering its very attractive price. The maximum sensitivity of the V4 series without option 020 is lower by 15dB.

• Option UBBV1, 40dB Low Noise External Broadband Preamplifier (1MHz-1GHz)
  

  This external super low-noise preamplifiers have a broad frequency range and high 40dB gain, enabling maximum performance particularly when measuring extremely weak signals at a EN55011, EN55022 or EN50371 EMC-test. If you use our BicoLOG antennas or our PBS1 Near Field Probe Set and EMC-Sniffer this broadband amplifiers are a MUST HAVE to get the best performance.

• Option UBBV2, 40dB Low Noise External Broadband Preamplifier (1kHz-8GHz)
  

  This external super low-noise preamplifiers have a broad frequency range and high 40dB gain, enabling maximum performance particularly when measuring extremely weak signals at a EN55011, EN55022 or EN50371 EMC-test. If you use our BicoLOG antennas or our PBS1 Near Field Probe Set and EMC-Sniffer this broadband amplifiers are a MUST HAVE to get the best performance.

• Option 205 (10GHz Broadband Peak Power Meter for HF-60100 V4 (X))
  

  This option expands your SPECTRAN with a Peak Power Meter with full 10GHz of bandwidth. Furthermore it allows exact measurement of signals with high crest factor like those of WLAN technology, and even extremely short signals, like Radar bursts. What's more, measurement is performed in real-time and broadband, while at the same time being temperature-compensated. It is also an perfect solution for measurement of cable attenuation or receiver output. Depending on the actual frequency, the Power Meter provides a sensitivity of up to approx. -50dBm, while the maximum usable level is +10dBm. By adding our 20dB attenuator (see price list), the maximum measurable signal level can be enhanced to +30dBm.

• Highend i5 EMF-Monitor
  

  SPECTRAN as a highend 19" rack version with built-in PC with an Intel i5-2405S, 8GB DDR3 (1333MHz) RAM, 320GB HDD, 1 x DVI-I (analog + digital), 1 x HDMI, extenal power supply (19.5 V, max. 7.9 A) and Linux operating system. Can be used as a standalone desktop PC or network SPECTRAN server. (Extra charge for PC € 500.00)

• 40dB Low Noise Internal Preamplifier
  

  This option provides an internal, super low-noise 40dB preamplifier, enabling maximum performance particularly when measuring extremely weak signals. This option is available for our SPECTRAN HF RSA and EMF Monitor HF series.

• 20dB Internal Attenuator
  

  Expands the measurement range from +20dBm to +40dBm. This option is available for our SPECTRAN HF RSA and EMF Monitor HF series.

• Software "EMF-Monitor"
  

  Advanced Logger- and Monitoring Software for continuous logging & streaming of any frequency range. Allows the access to unlimited numbers of RSA units by one web-interface only and from any point in the world. +€ 499.95

• EMI/EMC Near Field Probe Set Sniffer PBS1 or PBS2 (DC to 6GHz)
  

  Allows straightforward pinpointing and measurement of interference sources from DC to 6GHz in electronic component groups as well as execution and monitoring of generic EMC measuremen. Our near field probe set sniffer includes a total of 5 probes: 4 magnetic field probes and one electric field probe. You can find detailed information of the products on there shop page.

• 1m, 5m or 10m Low Loss SMA Cable
  

  High quality special SMA cable for connecting any HyperLOG®-Antenna or BicoLOG®-Antenna or the preamplifiers UBBV Series with various test equipment like Aaronia RF Spectrum-Analyzer. You can find more details about the article in our online shop.

• 20dB SMA Attenuator
  

  Expands the measurement range from +20dBm to +40dBm. More product details in our online shop.

• DC-Blocker (SMA)
  

  The DC-Blocker must be used if you want to measure DC powered signals like DSL/ISDN lines. It prevents the RF-input of the SPECTRAN to be destroyed by the DC-voltages. Simply connect the DC-Blocker to the SMA-input of your SPECTRAN. More product details in our shop.

• Calibration Resistor (SMA)
  

  Necessary to calibrate the SPECTRAN V4 noise-floor. The calibration resistor is a MUST-HAVE for any professional user! You can find more product information in our shop.

• Calibration Certificate
  

  For the pro user. Includes a detailed calibration sheet. More information about the article in our online shop.

Datasheet (pdf)

Ordersheet / Pricelist

Frequency Charts