RF Pre-amplifier 1MHz to 10GHz UBBV2

SPECTRAN Analyzer connected to UBBV Low noise Preamplifer

USB connector for Preamp calibration data readout

Broad band Preamplifier UBBV series

Included in delivery

  • UBBV2 RF Broadband Preamplifier
  • 2 mounting brackets for SPECTRAN
  • LiPo-Battery (integrated)
  • Battery charger and power supply incl. international adapter set
  • Aluminum carrying case with foam protection*
  • Detailed English manual (on CD)
  • SMA tool
  • Cleaning brush
      * If ordered with a SPECTRAN, the preamplifier will be supplied without carrying case (delivery within SPECTRAN carry case).

    Application examples

    • A "must have" for EMC measurements
    • Amplification of very weak signals
    • Boosts any antenna gain
    • Compensation of negative antenna gain

    Options

    • Currently there are no additional options available.

    Accessories

    • USB Cable (UBBV)

      To connect your external preamplifier to the PC. Special version with high performance EMC-ferrite. Highly recommended for PC use. You can find more product details in our online shop.

    • 1m, 5m or 10m Low Loss SMA Cable

      High quality special SMA cable for connecting any HyperLOG®-Antenna or BicoLOG®-Antenna or the preamplifiers UBBV Series with various test equipment like Aaronia RF Spectrum-Analyzer. You can find more details about the article in our online shop.

    • SMA to N Adapter

      To connect any Spectrum Analyzer etc. with N connector to the HyperLOG antenna (Above SMA cable needed). You can find more details in our online shop.

    • 20dB SMA Attenuator

      Expands the measurement range from +20dBm to +40dBm. More product details in our online shop.

    • DC-Blocker (SMA)

      The DC-Blocker must be used if you want to measure DC powered signals like DSL/ISDN lines. It prevents the RF-input of the SPECTRAN from being destroyed by the DC-voltages. Simply connect the DC-Blocker to the SMA-input of your SPECTRAN. More product details in our shop.

    Downloads

    Aaronia Low Noise Preamplifier

    Aaronia Low Noise RF PreAmp up to 8GHz

    Initiates file download
    frequency range of the spectrum analyzer
    € 999,95*
    (1MHz-10GHz)
    loading imagesloading imagesloading imagesloading imagesloading imagesloading imagesloading images

    Technical data

     

    • Frequency range: 1MHz to 10GHz (500kHz with 3dB difference)
    • Noise: 3,5dB (typ.)
    • Gain: 40dB (typ.) with "linear" fall off:
      1MHz: 40dB; 3GHz: 37.5dB; 6GHz: 35dB; 8GHz: 25dB; 10GHz: 20dB
    • Max. power at RF input: +15dBm
    • Max. power at RF output: +15dBm
    • Saturation power: -25dBm (50 ohms)
    • Input: 50 Ohm SMA (f)
    • Output: 50 Ohm SMA (m)
    • Weight: 146gr
    • Warranty: 10 years

     

    Highlights:

    • Suitable for any brand of Spectrum Analyzers or antennas
    • Fits perfectly to any SPECTRAN (mounting brackets included)
    • Runs with battery or external power supply
    • Integrated LiPo battery (up to 3,5h run time)
    • Integrated calibration data on EEprom (readout via integrated USB interface)
    • Very thick (2mm) aluminum housing offering very good screening
    • Includes international charger (110V/220V) and adapter

     

    40dB RF Broadband Preamplifier UBBV2

     

    High-End RF Preamplifier up to 10GHz. Works with any brand of Spectrum Analyzers and directly fits to any SPECTRAN. Broadband sensitivity increase by up to 40dB.

     

    Problems to read weak signals? Or how about boosting that probe gain or maybe preamping that antenna?
    The UBBV2 broadband preamp is the answer to all these needs as well as many others. You can use the UBBV2 anywhere a high gain, low noise amp is called for; digging out those weak shortwave signals or putting new life into that analyzer especially in the frequency range below 1GHz.
    Since the UBBV2 has such a high compression point of almost 100 milliwatts, you can even use it to boost the power of small micro transmitters!
    Newly designed microwave chips enable the UBBV2 to have gain up to 12GHz although we only spec the UBBV2 to 10 GHz. The UBBV2 is the ideal general purpose RF amp that you'll wonder how you got along without.

    Enables maximum performance particularly when measuring extremely weak signals. Highly recommended for EMC and Pre-Compliance tests like EN55011, EN55022, EN50371 etc..

    A "must have" to get the maximum performance out of any SPECTRAN unit.


    Made in Germany:

    All UBBV2 Preamplifier are developed, individually produced and calibrated in Germany at the Aaronia factory. This guarantees highest standard so that Aaronia can offer every customer a full 10 years warranty for all UBBV2 Preamplifiers.

     

    Included in delivery:

    All UBBV2 Preamplifier will be shipped with many accessories in a high-value aluminum carrying case. More details can be found at above section "Included in delivery".